Accessories for Zebra VC83-08SOCABAABA-I

Zebra Antenna - Dual Band (2.4Ghz/5Ghz) - 802.11a/b/g/n/ac - 2 dBi - RPSMA connector - Magnetic Mount - 2.9 meter cable. Used when the vehicle computer is used in indoor/outdoor areas where an externally mounted antenna is needed for better coverage

Zebra Whip Antenna (Stubby) - Dual Band (2.4Ghz/5Ghz) - 802.11a/b/g/n/ac - 2.4GHz 2dBi, 5GHz 3.7dBi - RPSMA connector - Magnetic Mount. Used when the vehicle computer is used in indoor/outdoor areas where an externally mounted antenna is needed for better coverage

Zebra Power Extension Cable DC, 6ft Waterproof

Zebra Power Extension Cable DC, 6ft Waterproof

Includes Screen Blanking feature

Zebra VC80 Side Mounted Holder for Scanner

Zebra VC80 U-MOUNT WITH VC70 HOLE PATTERN

The VC80 Series U-Mount is smaller than the one for the VC50 and has several mounting holes which allow drop-in replacements of VC70, and DLoGU-Mounts. It provides step less tilting of the VC and comes with the VC50 adapters.

Zebra ADAPTER FOR VC50 U-MOUNT

The adapter brackets for the VC50 U-Mount can be used to replace a VC50 by a VH10, VC80, VC80x or a VC8300 and reuse the existing U-Mount.

Zebra VC80, VH10 - VESA Plate Base - Can be used with the 4"" or 12"" RAM arm (MT4301 or MT4302) to mount a vehicle mount computer on any plane - Can also be attached to Quick Release Mount Plate (MT4205) - RAM D-size (2.25"") ball connected to a 4.75"" square plate with 4x100mm holes and 4x75mm holes in each corner - includes 4x bolts, nuts and lock washers

Zebra VC80, VH10 - Round Plate Base - Can be used with the 4"" or 12"" RAM arm (MT4301 or MT4302) to mount a vehicle mount computer on any plane - RAM D-size (2.25"") ball - Uses smaller footprint than VESA Plate (MT3501)

Zebra VC80, VH10 - Clamp Base (2"" max arm/bar) - Clamp can be used with the 4"" or 12"" RAM arm (MT4301 or MT4302) to mount a vehicle mount computer on any plane - Clamp the RAM arm on bars with square or rectangular cross section (2"" max. width) - RAM D-size (2.25"") ball

Zebra VC80, VH10 - Clamp Base (3"" max arm/bar) - Clamp can be used with the 4"" or 12"" RAM arm (MT4301 or MT4302) to mount a vehicle mount computer on any plane - Clamp the RAM arm on bars with square or rectangular cross section (3"" max. width) - RAM D-size (2.25"") ball

Zebra VC80, VH10 - Quick Release Mount - Allows a dismount of the vehicle mount computer without the need for tools - Can be used alone or in combination with the Cantilever Mount Kit (MT1002) or Vesa Plate Base (MT3501) 

includes Quick Release Mount that attaches to the sides of the vehicle mount computer and Mounting Plate (MT4205) that attaches to forklift

Zebra VC80, VH10 - 4"" RAM Mount - Short Arm - RAM D-size (2.25"") ball

Zebra VC80, VH10 - 12"" RAM Mount - Long Arm - RAM D-size (2.25"") ball

Zebra VC80, VH10 - RAM Rectangular Base with RAM D-size (2.25"") ball - 2"" x 3"" base - Base will install directly on the back of the vehicle mount computer

Zebra External Voltage Pre-Regulator - VC80, VH10 - 19-90V DC in, 15V DC out, 90W - Allows the installation of the vehicle mount computer on electric trucks with batteries greater than 48V 

Requires Power Supply Cable (CA1210) to connect to the vehicle power supply and Power Supply Extension Cable (CA1230) to connect to the VH10 or VC80, both sold separately

Zebra AC/DC Power Supply Kit - 100-240V AC, 12V DC, 6A, 72W - VC80, VH10

includes Power Supply (PWR-BGA12V72W0WW) and Power Cable Adapter (CA4000) 

Requires country specific three-wire grounded (C13) AC Line Cord sold separately

Zebra Enterprise Antenna 802.11 B/G

DIPOLE 2 DBI REVERSE POLARITY SMA CONNECTOR (STUBBY) 

Zebra Antenna - 2.4Ghz only - 802.11b/g - 5 dBi - RPSMA connector - Magnetic Mount - 2.9 meter cable. Used when the vehicle computer is used in indoor/outdoor areas where an externally mounted antenna is needed for better coverage

Zebra RIGHT ANGLE SMA REVERSE POLARITY PLUG-JACK ADAPTER

Zebra Power Extension Cable for Pre-Regulator with Ignition Sense

Zebra VC70 Power Cable to VH10 or VC80 Converter Cable - Allows VH10 or VC80 to be powered from VC70 power cable - Allows forklifts wired for VC70 to be easily converted to VH10 or VC80 - Requires VC70 Power Cable (25-159551-01)

Zebra Screen Protector - 5 Pack

Zebra VC80, VH10 - Rail Base (1-1/4"" to 1-7/8"" max. pipe diameter) - Clamp can be used with the 4"" or 12"" RAM arm (MT4301 or MT4302) to mount a vehicle mount computer on any plane - RAM D-size (2.25"") ball

Zebra VC80, VH10 - Rail Base (2"" to 2-1/2"" max. pipe diameter) - Clamp can be used with the 4"" or 12"" RAM arm (MT4301 or MT4302) to mount a vehicle mount computer on any plane - RAM D-size (2.25"") ball

Zebra VH10, VC80 - Mounting Plate for the MT4200 Quick Release Mount

Zebra VC80, VH10 - Adapter Bracket for the 82xx series Quick Release Mount

Zebra POWER SUPPLY AC/DC 100-240V 6.25A 150W

Requires: AC Power Cord

Zebra Stylus and Stylus Holder - VC80, VH10